Sculpting a laurel wreath on a shoulder pad


When I posted this pic the other week in my Salamander Commander conversion, I got a question from Mike over at Santa Cruz Warhammer about how I sculpted the shoulderpad on the far left (the circle with laurel under it).

Over the past year, I've sculpted a number of shoulderpads, from the simple to the complex.



Actually, both of those were complex ones despite looking relatively easy in the end. Regardless, it all comes down to understanding the object and breaking it down into smaller shapes that fit together and/or overlap.

We'll go back to the original one I got the question about.

STEP 1
I start with a blank shoulderpad. On that, I add a small, round blob of greenstuff in the center and start to press it down and outward. As I get close to the shoulderpad trim, I cut it (the excess greenstuff) away. The reason I don't press it all the way down and let it flow over the edges of the shoulderpad is because I'll lose my bearings and not keep a circle in the center. If I press down a little and then trim away a little, it becomes a series of small adjustments I make instead of one sweeping cut and hoping for the best. Remember, this circle needs to be centered but high enough to allow the laurel underneath.

As you press it down, pay attention to the thickness of your circle along the edge where you cut away the excess. You want a consistent thickness around the whole edge. If you need to peel it up and start over, then do what it takes. Spending a few minutes on the front end pays dividends in the end... especially if you're doing something like casting.

Getting the surface of the greenstuff smooth is easy enough, a wet finger tip does the job just fine. Just watch your pressure so you don't leave any fingerprints.

Here is the most important part of all:
LET IT CURE COMPLETELY BEFORE MOVING ON.

Stop, go back and read that last sentence again.
If you think you're going to have trouble with this particular step, you need to rethink sculpting to be honest.

Patience is perhaps the biggest sinlge thing you need to have when it comes to sculpting. So let's move on.

With the circle sculpted and cured, we move onto the laurel itself. There are lots of ways to sculpt things. I'm going to go with a real simple approach here that doesn't require any complicated math or measuring or the moon and stars being lined up just right. We're looking for a suggestion of a laurel here, we don't need to sculpt each individual leaf.

Now you do the same thing for each side of the laurel.
Once you have both sides done and they've cured, you can add a tiny ball of greenstuff to the center of the laurel and flatten it out to get the center gem/medallion in there if you want.

STEP 2
Lay a thin length of greenstuff starting at the bottom (in the center) and going up one side. Cut the top off where you want it to stop.

Press down the greenstuff and flatten it slightly in position.

STEP 3
Cut a groove down the center of the flattened greenstuff. Don't drag your tool in this step since it may "pull" the greenstuff out of shape. Just make nice single line indentation up the middle.

Press a series of smaller grooves along each side of the center line. These will represent the leaves.

When you get to the top, you can cut a wedge out of the top to give the illusion of leaves. It's not necessary, but it helps make it look convincing.

STEP 4
This isn't really a step, just clean up any edges that catch your attention, and that's not even a "have to" do either. Make sure both sides of the laurel line up and look the same, you don't want it to be lopsided.
That's it really, simple as that.

I will say that as you do more and more sculpting, you'll develop an idea of what's going to happen to the greenstuff before you cut it and you'll learn how much pressure to apply and in what position you need to hold the blade exactly and so on to get what you want the first time. I don't think this kind of thing can be taught, it's something I've just sort of learned as I've gone along with my sculpting. When I started, what used to take me three or four attempts with numerous cuts and fixing-up now is done on the first or second try.


Ron, From the WarpIf you've got any questions about something in this post, shoot me a comment and I'll be glad to answer. Make sure to share your hobby tips and thoughts in the comments below!