Painting Minotaurs in bronze and a banner

Minotaurs Space Marine with bolter

With Forge World releasing their new resin Minotaur shoulderpads and getting an email from a reader about painting Minotaurs, I thought I might see how hard it would be to paint the new "bronze" color scheme Forge World has them wearing now.

The best part of this whole thing is I found the perfect use for my pot of Tin Bitz that has been lying around for ages.

The actual painting process is fairly quick
Once you have your guy assembled, it's a quick prime of black followed by a good basecoat of GW Tin Bitz. You don't have to worry about where you get it either, just slap the stuff on.

Minotaur armour patina effect

Once that dries, it's a liberal wash of slightly thinned GW Hawk Turquoise over the whole model. Again, no need to worry about where it goes. Just make sure you cover the whole model (Step 1). Make sure that has time to dry completely before moving onto steps two and three. Once your Hawk Turquoise wash is completely dry, take your Tin Bitz and give the model a good drybrush of the basecolor again (Step 2).

They key with this step is to make sure your larger armour plates get good coverage. After your done with that, it's a matter of one more drybrush of Folk Art Metallic Solid Bronze (step 3). I think this is close to GW Dwarf Bronze if memory serves me correct.

Apply this final lighter bronze color to the upper portions of the model only where the light would hit the surfaces. This is in effect our highlighting on the model. It also gives the model a warmer look than just having the Tin Bitz on there.

And that's it for the amrour. Simple as that.
The rest of it is a matter of finishing off the details on the model.

The details bring it to life
I will add that it's worth going in and adding some shadows to the deeper recessed areas on the model. This helps with defining the armour plates and removing a tiny amount of the patina effect so it's not too overpowering. We go heavy with the effect in the beginning so we can remove it as we want. It's easier than trying to build it up at this point.


In this picture, you can see where I took and applied a quick wash of GW Badab Black. It's only in the deepest recesses so it helps with the overall shape of the model.

When it came to heraldry, I had to sort of make it up since I don't have the latest Imperial Armour book yet. I chose the red shoulderpads as a way to break up the huge amount of bronze on the model. I don't know the significance of the red, but it comes from IA10 so it must be good right?

The red started out as GW Foundation Mechrite Red with a thin layer of GW Red Gore and a wash of Baal Red to darken it down. I didn't want it to pop out on the model and compete with the gold so I kept it really dark. Badab Black carefully applied around the trim really made it darken down considerably.


I'm guessing he's got a tactical Squad arrow outline on his right shoulder and some kind of Veteran status markings on his left. Both are easy enough to do, the only thing you have to be careful of is working over the completed (highlighted and shaded) shoulderpad... any mistakes and you'll be stuck painting the whole thing over again. Freehand shouldn't scare you away if you know what to watch for when doing it.

The trick was to lightly draw the markings with a pencil and then go over that with the paint. The pencil is just dark enough to see, but comes off easily enough with a damp Q-Tip when done.

Some additional weathering
I did go through and apply a few powders to some key spots and used a pencil to add some wear and tear along the more prominent edges of some armour plates. The pencil is a great effect and quick too. The powders I used in this case were Exhaust Black (around the lower portion of the shoulderpads) and Metallic Iron (on the backpack and boltgun). Both are from Secret Weapon Minis.

The pencil weathering technique is explained more in this post here.

The base and slushy snow effect
The base also comes from Secret Weapon Minis and I decided to try making what I thought would pass for slushy snow. Actually, there's moss molded onto the base and I could not find my moss material to save my life. These are the same bases the Storm Wardens team used and I've always loved how they look.

The snow itself comes from Gale Force Nine. All I did was apply some white (PVA) glue to the base and sprinkle the stuff on. After is was dry, I went in with a slightly diluted GW Devlan Mud wash and dabbed it onto the snow in a few places to make it look like it's picked up some of the dirt from underneath it.

There are lots of ways to do snow, here are a few more here.

And last but not least, the banner
Minotaurs bannerAs part of the banner collection I'm putting back up, I dug this guy out and included him here. He's also on the banner page too. It's a little old school, but it might help those who have nothing else and you can always change it to suit your needs.

Just click and save it to your desktop. Print it out from there to the size you want.

All in all, this guy came out better than I thought he might. I was worried at first about getting the right amount of patina on the armour, but it came out okay in the end.

I'm still partial to their old school look, but the new bronze doesn't look too bad either.

Make sure to check out these posts as they might help:
Adding freehand, the pros and cons of when to do it
Basing with snow, a few methods to get the look you want
Another look at painting metallics

A few more unposted/WIP model shots




Ron, From the WarpIf you've got any questions about something in this post, shoot me a comment and I'll be glad to answer. Make sure to share your hobby tips and thoughts in the comments below!